|
|
|
|
|
|
|
|
|
Full annealing
| Глоссарий в области цветной металлургии |
|
Полный отжиг, русский
Термин, который обозначает цикл отжига для получения минимальной прочности и твердости. состав и начальное состояние материала и используемого цикла температуры-времени должны быть определены.
|
Anneal, английский
- To subject to heat with subsequent cooling. when annealing copper; the act of softening the metal by means of heat to render it less brittle.
- Отжиг
- Heating metal to above its critical temperature range, then slowly cooling to remove stresses, induce softness, remove gases, alter ductility, induce toughness, or modify electrical, magnetic or other physical properties.
Anneal to temper, английский
Annealed glass, английский
Glass created by a process that moves it, in a molten form, along a long oven where it is heated and then slowly cooled under controlled conditions, emerging as a flat, “fire polished” glass product.
Annealed proton exchange, английский
Annealed tube, английский
Annealed wire rope, английский
Annealing, английский
- A heating and cooling operation implying usually a relatively slow cooling. annealing is a comprehensive term. the process of such a heat treatment may be
- A process of holding a material at an elevated temperature, but below its melting point, to permit the relieving of internal stresses in the material. annex, annexe a subsidiary structure near or adjoining a larger principal building.
- Отпуск; отжиг annex(е) пристройка; вспомогательное строение
- Formation of hydrogen bonds between the nucleotide base pairs of two single-stranded complementary nucleic acid sequences
- Process of heating and cooling a material, usually to reduce residual stresses or to make it softer.1 part 1. terminology
- Process of heating a material to, and holding at, a desired temperature followed by cooling at a desired rate, usually to reduce residual stresses or bring about some other desired change.
- Process of heating a material to, and holding at, a desired temperature followed by cooling at a desired rate, usually to reduce residual stresses or bring about some other desired change. (for steels, the annealing process is called normalization.) see also heat treatment; tempering.
Annealing color, английский
Annealing conditions, английский
Annealing oven, английский
Annealing separator, английский
Разделяющий слой при отжиге тонкого стального листа
Annealing to critical range, английский
Отжиг в подкритическом интервале
Annealing to granular cementite, английский
Отжиг на зернистый цемент, сфероидизация
Annealing twin, английский
Двойник отжига (двойник, образовавшийся при отжиге)
Annealing-twin bands, английский
Двойниковые полосы при отжиге
Full, английский
- Полный, широкий (о туловище)
- Thrust, standard стандартная полная тяга
- (the adverb fullwise appears in the records department`s written orders.)
- Cape house full-centered applied to an architectural feature the outline of which follows an arc of a circle.
- Of a dimension, slightly oversize.
- A полный sentence, stop, translation
- Not luffing,
- The state of the sails when the wind fills them so as to carry the vessel ahead.
- The state of sails when bellied-out by wind.
- 32-bit полностью 32-разрядный full-blown pc полнофунциональный пк; "полноценный" персональный компьютер
- When used to describe a sound`s tonal balance, complete or near-complete reproduction of low or fundamental frequencies, with adequate level around 200 hz. a sound with strong fundamental frequencies relative to harmonics. female voices tend to sound full around 250 hz, whereas male voices sound full around 125 hz.
Full, шведский
Full, английский
Full (detailed) classification, английский
Подробная (детализированная) классификация но. full repair — капитальный ремонт, см. capital repair
Full -, английский
Прицеп (двухосный)
Full - scale test, английский
|
Full center, английский
Friction welding, английский
|
|
|
|
|
|
|
